高圣部品
HIGH HOLY PARTS
HIGH HOLY PARTS
專業電子開關、插座、連接器、精密彈簧廠家
專業為您提供完善的售前、售后服務
專業為您提供完善的售前、售后服務
|
主要技術參數/ Main data |
|||
| 1、RATING（額定值）：1.5A 125V AC | |||
| 2、FUNCTION（接觸型式）：1P2T | |||
| 3、TIMING（時間特性）：NO SHORTING | |||
| 4、ELECTRICAL CHARACTERISTICS（電氣性能規格） ： | |||
| ITEM 項目 | TEST CONDITIONS 測試條件 | PERFORMANCE 規格 | |
| 4.1 |
CONTACT RESISTANCE 接觸電阻 |
MEASURED AT SMALL CURRENT(100mA OR LESS) 在微小電流(100mA)以下，撥動三次后測試. |
100mΩMAX. 100毫歐以下. |
| 4.2 |
INSULATION RESISTANCE 絕緣電阻 |
APPLY A VOLTAGE OF 500V DC FOR 1 MIN. TO FOLLOWING PORTIONS AFTER WHICH MEASUREMENT SHALL BE MADE. {C}(1)BETWEEN BODY AND TERMINAL {C}(2)BETWEEN TERMINALS 輸入500V DC 電壓1分鐘,按以下接觸方法測試: {C}(1)外殼與排腳之間。 {C}(2)端子之間。 |
100MΩMIN. 100兆歐以上. |
| 4.3 |
DIELECTRIC STRENGTH 耐電壓 |
AC500V(50-60Hz)FOR 1 MIN TRIP CURRENT:0.5mA
BETWEEN TERMINALS. BETWEEN INDIVIDUAL TERMINALS AND FRAME. 輸入500V(50-60Hz)電壓,1分鐘感度電流為0.5mA,按以下接觸方法測試: (1)排腳相互之間 (2)排腳與外殼之間 |
WITHOUT DAMAGETOPARTS
ARCING OR BREAKDOWN
ETC 沒有絕緣破壞等異常 |
| 5、MECHANICAL CHARACTERISTICS (機械性能規格) | |||
| ITEM 項目 | TEST CONDITIONS 測試條件 | PERFORMANCE 規格 | |
| 5.1 |
OPERATING FORCE 作動力 |
MEASUREMENT SHALL BE MADE ST THE NEAREST POINTF
OF THE COMPONENT OR AT THE POINT 3mm FROM THE
TIP OF THE ACTUATOU(KNOB0) 在距離膠柄3mm作測定點，撥動三次后測試。 |
300gf±100gf |
| 5.2 |
TERMINAL STRENGTH 端子強度 |
A STATIC LOAD OF(500gf)SHALL BE APPLIED
TO THE TERMINAL FOR 15 SEC,IN ANY DIRECTON. 在排腳前端任意一個方向加(500gf)力度測試,時間為15秒. |
MECHANICAL AND
ELECTRICAL
CHARACTERISTICS SHALL
BE SATISFIED WITHOUT
LOOSENESS
OF ACTUATOU. 在端子中沒有裂開,松動等異常,滿足于機械、電器性能。 |
| 5.3 |
DISPLACEMENT OF ACTUATOR (KNOB) 柄強度 |
A STATIC LOAD OF 10N(1Kgf)SHALL BE APPLIED
TO THE TOP OF THE ACTUATOR(KNOB)AND THEN
DESPLACEMENT SHALL BE MEASURED TO THE
DIRECTION OF THE ARROW. 在柄的前端施加1Kgf的力度,位移應沿印記的方向上定. |
THE LEVER SHALL HAVE
NO SERIOUS DEFORMATION
AND FUNCTION IS
NORMALLY. 柄部無嚴重變形,可以正常工作 |
| 6、ENDURANCE CHARACTERISTICS (耐久性) : | |||
| ITEM 項目 | TEST CONDITIONS 測試條件 | PERFORMANCE 規格 | |
| 6.1 |
LIFE TEST 壽命試驗 |
ENDURANCE WITHOUT LOADING： A SWITCH SHALL BE SUBJECTED TO 10,000 CYCLES AT A SPEED OF 15 TO 18 CYCLES PER MINUTE WITHORT LOADING. 無負荷: 在無負荷的條件下以每分鐘15—18回的速度進行10,000次的測試. |
(1)CONTACT RESISTANCE(接觸電阻)
200mΩ MAX.200毫歐以下. (2)INSULATION RESISTANCE(絕緣電阻) 50MΩ MIN. 50兆歐以上. (3)WITHSTAND VOLTAGE(耐電壓) AC 500V,1 MINUTE.AC 500V 1分鐘 (4)OPERATING FORCE(作動力) ±30%INITIAL VALUE. 變化范圍初始值±30% (5)WITHOUT DAMAGE TO PARTS ARCING OR BREAKDOWN ETC. (測試后外表無損傷,并且滿足機械性能) |
| 6.2 |
SOLDERA-BILITY TEST 可焊性試驗 |
THE TOP OF THE TERMINALS SHALL BE
DIPPED 2mm IN THE SOLDER BATH OF
230±5℃ FOR 3±0.5 SECONDS. 端子頂部被浸入錫焊池中2mm深,溫度為 230±5℃,時間為3±0.5秒. |
(1) SOLDER WELTING TIME SHALLBE
3 SEC OR LESS. 焊接時間少于3秒 (2) THE AREA OF SOLDERING SHOULD BE OVER 75% 焊接面積要有75%以上. |
| 6.3 |
RESISTANCE
TO
SOLDERING
HEAT TEST 耐焊性試驗 |
SOLDER BATH METHOD: SOLDER TEMPERATURE 260±5℃ IMMERSION TIME3±0.5 SEC IMMERSION DEPTH UP TO THE SURFACE OF THE BOARD 1.6mm DIMENSIONS OF COMPONENT HOLES IN THE PRINTED WIRING BOARD SHALL BEING ACCORDANCE WITH THOSE SPECIFIED IN THES SPECIFICATION. 焊爐焊接的時候溫度控制在260±5℃,過爐時間為3±0.5秒,于基板厚度為1.6mm SOLDERING IRON METHOD: BIT TEMPERATURE 350±10℃ APPLICATION TIME OF SOLDERING IRON3±0.5SEC HOWEVER EXCESSIVE PRESSURE SHALL NOT BE APPLIED TO THE TERMINAL. 手焊接的時候溫度控制在350±10℃,時間為3±0.5秒,但不能在排腳上施加異常壓力 |
WITHORT DEFORMATION OF CASE OR
EXCESSIVE LOOSENESS OF TEMINALS
ELECTRICAL CHARACTERISTCS SHALL
BE SATISFIED. 本體無變形,能滿足于機械、電氣性能。 |
| 6.4 |
COLD TEST 耐冷試驗 |
THE SWITCH SHALL BE STORED AT A TEMPERATURE OF -25±3℃ FOR48HOURS.
THEN THE SWITCH SHALL BE MAINTAINED
AT STANDARD ATMOSPHERIC CONDITIONS
FOR 1 HOUR AFTER WHICH MEASUREMENT
SHALL BE MADE. 放置在溫度-25±3℃中48小時后,再放置常溫中1小時來進行測試. |
THERE SHALL BE NO DEFORMATION
OR CRACKS IN MOLDED PART. 外觀無異常,滿足于機械、電氣性能 |
| 6.5 |
HEAT TEST 耐熱試驗 |
THE SWITCH SHALL BE STORED ATA
TEMPERATURE OF70±2℃ FOR 48 HOURS.
THEN THE SWITCH SHALL BE MAINTAINED AT
STANDARD ATMOSPHERIC CONDITIONS FOR 1
HOUR AFTER WHICH MEASUREMENT SHALL BE MADE. 放置在溫度70±2℃中測試48小時后,再放置正常室溫中1小時來測定. |
THERE SHALL BE NO DEFORMATION OR CRACKS IN
MOLDED PART. 外觀無異常,滿足于機械、電器性能. |
| 6.6 |
HUMIDITY
TEST 潮濕試驗 |
THE SWITCH SHALL BE STORED ATA TEMPERATURE
OF 40±2℃ AND A HUMIFITY OF 90% TO 95%
FOR 96 HOURS.THEN THE SWITCH SHALL BE MAINTAINED AT STANDARD ATMOSPHERIC CONDITION FOR 1 HOUR AFTER WHICH MEASUREMENT SHALL BE MADE. 放置40±2℃的相對濕度為90%～95%環境中96小時后,再將樣板放在正常環境1小時后進行測試. |
|
| 6.7 |
STANDARD
ATMOSPHERE
CONDITIONS 測試標準狀態 |
UNLESS OTHERWISE SPECIFIED.
THE STANDARD RANGE OF ATMOSPHERE
CONDITIONS FOR MAKING MEASUREMENTS
AND TESTS ARE AS FOLLOWS: (1)AMBIENT TEMPERATURE:5℃ TO 35℃ (2)RELATIVE HUMIDITY:45% TO 85% (3)AIT PRESSURE :86Kpa TO 106Kpa 在沒有指定的情況下測試溫度、濕度、氣壓如下: (1)溫度為5℃—35℃. (2)濕度為45%—85%. (3)氣壓為86Kpa—106Kpa. |
|
| 6.8 |
PRACTICAL
TEMPERATURE
RANCE 使用溫度范圍 |
AT-16℃—+60℃. 在-16℃—+60℃內使用. |
|
